Sliding and Swing Driveway Gates for Edgware Frontages
Metal driveway gates made to the opening, hung on posts that can carry them, swinging or sliding to suit the ground.
A driveway gate is the heaviest single thing most people ever hang on their house, and almost every failure we are called to is the same failure: a good gate on posts that were never sized to carry it.
The first decision is not the pattern, it is swing or slide. A swing pair needs room to open and reasonably level ground. A sliding gate needs a clear run alongside the opening but almost no space in front, which is what makes it the answer on a short drive that meets the pavement.
Everything after that is measurement. The opening is surveyed, the fall across it is checked, and the leaves are made to those figures rather than trimmed from a stock pair on the morning of the fit.
What we actually fit
- Configurations
- Single leaf, double swing pair, or sliding on a track or cantilever
- Typical width
- Two and a half to five metres for a domestic drive, wider as a sliding leaf
- Posts
- Steel posts sized to the leaf weight and concreted deep, not bolted to a slab edge
- Ironmongery
- Galvanised heavy duty hinges, adjustable where the ground is uneven, drop bolts on a pair
- Automation
- We build gates prepared for automation and work alongside your automation installer. We do not carry out the electrical installation ourselves.
Ironmongery is where cheap gates give themselves away. Hinges, drop bolts and keeps are galvanised throughout, because a rusted hinge pin on a heavy leaf is not a cosmetic problem.
Edgware in practice
Side-return access on Edgware semis is genuinely narrow — long panels often have to come up over the garage, and that is a post problem before it is a gate problem. Gate posts here are sized to the finished leaf weight and concreted deep, because a leaf that heavy will find any weakness in a foundation within a season.
Where a gate opens onto a busy stretch off A5 Edgware Road / A41 we look at pedestrian visibility and whether an outward swing is sensible at all. On those frontages a sliding leaf is often the safer specification and we will say so before quoting.
Most Edgware drives we gate are shorter than the owner thinks, which is why the swing or slide question gets settled with a tape measure on the visit. 1930s semis built around the Tube extension, plus newer flats near the town centre typically leave a car length between the pavement and the house, and a swinging pair needs that space to be genuinely clear.
When we recommend it
- Drives where the frontage needs closing off and the ground is level enough to swing a pair
- Short drives that meet the pavement, where a sliding leaf avoids swinging over a public footway
- Frontages already carrying railings, where a matching gate makes the line continuous
- Replacing a timber pair that has dropped and dragged for years
If the drive slopes up sharply from the pavement, a swinging pair will ground before it is halfway open and no hinge fixes that. Either the ground gets levelled, the gate opens outward with the visibility implications that carries, or it slides. We will tell you which on the visit rather than after installation.
The order of work
1. Survey the opening
Width, the fall across the opening, the pavement line and where a car actually stops are all measured, because those four figures decide the configuration.
2. Posts first
Posts are sized to the finished leaf weight and concreted, and where automation is planned we set the ducting at this stage rather than digging the drive up twice.
3. Hang and adjust
Leaves hung, drop bolts and stops set, and the swing checked through its full arc with the gate loaded, not empty.
What people ask us
- Can you automate the gates?
- We build gates prepared for automation, including the post sizing and ducting, and we work alongside your automation installer. We do not carry out the electrical installation ourselves and we would rather say that than pretend otherwise.
- Can new metal gates match my existing railings?
- Yes. Where there is an existing railing run we match the bar centres, the head detail and the powder coat colour so the gate reads as part of the boundary rather than as a later addition.
- Should I have swing gates or a sliding gate?
- Swing if you have level ground and space in front to open into. Slide if the drive is short, meets the pavement, or slopes. A sliding leaf needs a clear run alongside the opening, so the deciding factor is usually what is beside the drive rather than in front of it.
- Do I need permission for driveway gates?
- Gates next to a highway have height limits under permitted development, and a listed building or conservation area changes the picture. We flag it at quote stage so you can check with the council before anything is fabricated.
- Why did my old gates start dragging?
- Nearly always the posts rather than the gates. A timber post moves in the ground and a leaf that is a hundred kilos amplifies a few millimetres of lean into a gate that catches. That is why we size and concrete steel posts to the leaf.
- How soon can you look at a job in Edgware?
- Usually within a few days. We are working across Barnet Council most weeks, so a measured visit for driveway gates, sliding and swing rarely needs a long wait. Call 07885907880 and we will give you a date rather than a vague promise.
Driveway gates measured on site in Edgware
We measure the opening, the fall and the approach, then quote the leaves, the posts and the ironmongery separately. Free site visit, written quote, and cards accepted once the price is agreed.
Related metal work: Railings and estate fencing, Bow top fencing, Side and pedestrian gates. Main hub: metal fencing and gates.
Nearby: Driveway gates in Mill Hill, Driveway gates in Bushey, Driveway gates in Finchley.
Get My Free Quote — 24h Response
No callout fee · Free site visit · Friendly local team covering London & Hertfordshire.
Pay by debit or credit card, bank transfer or cash once the work and price are agreed. No deposit taken online.