Should the tops be pointed or blunt?

Pointed heads deter climbing and are common on perimeters. Blunt heads are used where the public, and particularly children, are close to the line. The right answer depends on who is on each side of the fence.

Can vertical bar take a matching gate?

Yes, and it should. A gate leaf in the same pattern with a heavier frame and commercial hinges keeps the line continuous, which is what stops the gate becoming the weak point.

Does it need maintenance?

A wash and an occasional check on the hinges and fixings. There is no annual repainting on a galvanised and powder coated line, which is where the cost comes back compared with timber.

Can it be fitted onto an existing wall or kerb?

Yes, on base plates bolted down where the substrate is sound. We check what is actually under the surface first, because bolting a two metre fence to a thin slab moves the failure from the fence to the concrete.

What height should a perimeter vertical bar fence be?

It depends on what you are protecting, but 2000mm to 2400mm is the usual range for a site perimeter, and below about 1800mm it stops being a deterrent. We will tell you honestly if the height you have asked for will not do the job you have described.

Do you cover the whole of Borehamwood?

Yes, vertical bar fencing across WD6 and the surrounding Hertfordshire towns, including bushey, barnet, watford. The site visit and the written quote are free wherever you are in that area.

Vertical bar fencing in Borehamwood

Borehamwood Vertical Bar Fencing, Specified Not Guessed

The workhorse steel boundary: vertical bars through horizontal rails, sized from a light frontage run up to a genuine perimeter.

Vertical bar is the specification that scales. The same basic idea, bars passing through top and bottom rails, covers a 900mm run across a communal frontage and a 2400mm perimeter around a substation, and the difference between them is section size, bar centres and head detail rather than a different product.

That is why it is the most specified metal fence in the country and the one most often bought wrongly. A light domestic section put on a perimeter looks the part and bends the first time a wheelie bin is dragged into it.

We price the section rather than the picture. Tell us what the boundary has to resist and how often it gets hit, and the bar diameter, the rail size and the post centres follow from that.

The numbers that matter

Typical height: 900mm frontage runs up to 2400mm perimeter lines
Head detail: Blunt top, pointed top or extended bar above the top rail
Bar centres: Set to the brief, closed up where climbing or through reach is the concern
Rails: Two rails as standard, three where height or impact loading calls for it
Finish: Hot dip galvanised then powder coated for the full section, welds included

On tall runs the galvanising is not optional. A powder coat alone over bare steel will fail at every drilled hole and weld within a couple of winters, and once it starts you are repainting the whole line.

Doing this job in Borehamwood

The vertical bar work around Borehamwood splits cleanly: light runs on communal frontages, and heavier sections around Elstree Way and Imperial Place Business Park. They are quoted as two different products because they are two different products, and pricing them off one rate per metre is how a boundary ends up under specified.

Vehicle movement decides gate sizing on most Borehamwood sites. We check the swept path against the access off A1 / A5135 and the turning available inside the gate line before quoting a leaf width, because a gate that cannot be opened fully in practice is a gate that gets left open.

Limited rear access on the older estates means materials usually have to come through the house, which is why post holes on taller runs here get sized to the exposure rather than to a standard depth. On a 2400mm line the foundation is the fence.

What it suits

Site perimeters, yards, substations, pumping stations and utility compounds
Communal frontages where a mesh line would look institutional
Boundaries beside parking where vehicles will occasionally make contact
Anywhere the boundary has to be seen through for surveillance

If the brief is privacy, vertical bar fails it completely. It is a see through boundary and it always will be. It is also more expensive per metre than weld mesh at the same height, so where appearance genuinely does not matter, mesh is the better value answer.

Vertical Bar Fencing fitted in Borehamwood, WD6 (1)

Vertical Bar Fencing fitted in Borehamwood, WD6 (2)

Vertical Bar Fencing fitted in Borehamwood, WD6 (3)

How the job runs

1. Survey the line
Levels, existing kerbs, drainage runs and vehicle swept paths are checked before section sizing, because a gate that fouls a kerb is a redesign not a snag.
2. Foundations
Post holes sized to the height and the exposure, concreted, with deeper settings where the run is tall or the ground is soft.
3. Install and hand over
Bays fitted, welds and cut ends made good, and a written record of the specification handed over with the invoice.

Questions we get asked

Should the tops be pointed or blunt?: Pointed heads deter climbing and are common on perimeters. Blunt heads are used where the public, and particularly children, are close to the line. The right answer depends on who is on each side of the fence.
Can vertical bar take a matching gate?: Yes, and it should. A gate leaf in the same pattern with a heavier frame and commercial hinges keeps the line continuous, which is what stops the gate becoming the weak point.
Does it need maintenance?: A wash and an occasional check on the hinges and fixings. There is no annual repainting on a galvanised and powder coated line, which is where the cost comes back compared with timber.
Can it be fitted onto an existing wall or kerb?: Yes, on base plates bolted down where the substrate is sound. We check what is actually under the surface first, because bolting a two metre fence to a thin slab moves the failure from the fence to the concrete.
What height should a perimeter vertical bar fence be?: It depends on what you are protecting, but 2000mm to 2400mm is the usual range for a site perimeter, and below about 1800mm it stops being a deterrent. We will tell you honestly if the height you have asked for will not do the job you have described.
Do you cover the whole of Borehamwood?: Yes, vertical bar fencing across WD6 and the surrounding Hertfordshire towns, including bushey, barnet, watford. The site visit and the written quote are free wherever you are in that area.

Ask us to size it before you buy it

Most under specified fences we replace were bought on price per metre alone. Call 07885907880 for a free site visit and a written specification you can compare like for like.

Related metal work: Palisade fencing, Galvanising and powder coating, Weld mesh fencing. Main hub: metal fencing and gates.

Nearby: Vertical bar fencing in Bushey, Vertical bar fencing in Barnet, Vertical bar fencing in Watford.

Get In Touch