Can vertical bar take a matching gate?

Yes, and it should. A gate leaf in the same pattern with a heavier frame and commercial hinges keeps the line continuous, which is what stops the gate becoming the weak point.

What height should a perimeter vertical bar fence be?

It depends on what you are protecting, but 2000mm to 2400mm is the usual range for a site perimeter, and below about 1800mm it stops being a deterrent. We will tell you honestly if the height you have asked for will not do the job you have described.

Should the tops be pointed or blunt?

Pointed heads deter climbing and are common on perimeters. Blunt heads are used where the public, and particularly children, are close to the line. The right answer depends on who is on each side of the fence.

Can it be fitted onto an existing wall or kerb?

Yes, on base plates bolted down where the substrate is sound. We check what is actually under the surface first, because bolting a two metre fence to a thin slab moves the failure from the fence to the concrete.

Does it need maintenance?

A wash and an occasional check on the hinges and fixings. There is no annual repainting on a galvanised and powder coated line, which is where the cost comes back compared with timber.

Is access a problem for vertical bar fencing around N4?

It is planned rather than discovered. Deliveries come in off A105 Green Lanes / A503 Seven Sisters Road, and where a street near Turnpike Lane, Wood Green, Harringay (Piccadilly / Overground) is tight we arrange the offload and the carry before the start date so nobody spends the morning blocking a road.

Vertical bar fencing in Haringey

Vertical Bar Perimeters and Frontages in Haringey

The workhorse steel boundary: vertical bars through horizontal rails, sized from a light frontage run up to a genuine perimeter.

Vertical bar is the specification that scales. The same basic idea, bars passing through top and bottom rails, covers a 900mm run across a communal frontage and a 2400mm perimeter around a substation, and the difference between them is section size, bar centres and head detail rather than a different product.

That is why it is the most specified metal fence in the country and the one most often bought wrongly. A light domestic section put on a perimeter looks the part and bends the first time a wheelie bin is dragged into it.

We price the section rather than the picture. Tell us what the boundary has to resist and how often it gets hit, and the bar diameter, the rail size and the post centres follow from that.

Local notes for Haringey

The vertical bar work around Haringey splits cleanly: light runs on communal frontages, and heavier sections around Wood Green High Road and Green Lanes (Harringay Ladder) and Tottenham High Road. They are quoted as two different products because they are two different products, and pricing them off one rate per metre is how a boundary ends up under specified.

We work across Haringey Council and can phase a perimeter so a live site is never left open. Where deliveries have to route via A406 North Circular (5 min) / M25 J25 (20 min) we book them around your access hours rather than ours.

Vehicle movement decides gate sizing on most Haringey sites. We check the swept path against the access off A105 Green Lanes / A503 Seven Sisters Road and the turning available inside the gate line before quoting a leaf width, because a gate that cannot be opened fully in practice is a gate that gets left open.

Specification at a glance

Typical height: 900mm frontage runs up to 2400mm perimeter lines
Head detail: Blunt top, pointed top or extended bar above the top rail
Bar centres: Set to the brief, closed up where climbing or through reach is the concern
Rails: Two rails as standard, three where height or impact loading calls for it
Finish: Hot dip galvanised then powder coated for the full section, welds included

On tall runs the galvanising is not optional. A powder coat alone over bare steel will fail at every drilled hole and weld within a couple of winters, and once it starts you are repainting the whole line.

From visit to handover

1. Survey the line
Levels, existing kerbs, drainage runs and vehicle swept paths are checked before section sizing, because a gate that fouls a kerb is a redesign not a snag.
2. Foundations
Post holes sized to the height and the exposure, concreted, with deeper settings where the run is tall or the ground is soft.
3. Install and hand over
Bays fitted, welds and cut ends made good, and a written record of the specification handed over with the invoice.

Vertical Bar Fencing fitted in Haringey, N4 (1)

Vertical Bar Fencing fitted in Haringey, N4 (2)

Vertical Bar Fencing fitted in Haringey, N4 (3)

Who buys this and why

Site perimeters, yards, substations, pumping stations and utility compounds
Communal frontages where a mesh line would look institutional
Boundaries beside parking where vehicles will occasionally make contact
Anywhere the boundary has to be seen through for surveillance

If the brief is privacy, vertical bar fails it completely. It is a see through boundary and it always will be. It is also more expensive per metre than weld mesh at the same height, so where appearance genuinely does not matter, mesh is the better value answer.

Before you buy, the usual questions

Can vertical bar take a matching gate?: Yes, and it should. A gate leaf in the same pattern with a heavier frame and commercial hinges keeps the line continuous, which is what stops the gate becoming the weak point.
What height should a perimeter vertical bar fence be?: It depends on what you are protecting, but 2000mm to 2400mm is the usual range for a site perimeter, and below about 1800mm it stops being a deterrent. We will tell you honestly if the height you have asked for will not do the job you have described.
Should the tops be pointed or blunt?: Pointed heads deter climbing and are common on perimeters. Blunt heads are used where the public, and particularly children, are close to the line. The right answer depends on who is on each side of the fence.
Can it be fitted onto an existing wall or kerb?: Yes, on base plates bolted down where the substrate is sound. We check what is actually under the surface first, because bolting a two metre fence to a thin slab moves the failure from the fence to the concrete.
Does it need maintenance?: A wash and an occasional check on the hinges and fixings. There is no annual repainting on a galvanised and powder coated line, which is where the cost comes back compared with timber.
Is access a problem for vertical bar fencing around N4?: It is planned rather than discovered. Deliveries come in off A105 Green Lanes / A503 Seven Sisters Road, and where a street near Turnpike Lane, Wood Green, Harringay (Piccadilly / Overground) is tight we arrange the offload and the carry before the start date so nobody spends the morning blocking a road.

Ask us to size it before you buy it

Most under specified fences we replace were bought on price per metre alone. Call 07885907880 for a free site visit and a written specification you can compare like for like.

Related metal work: Side and pedestrian gates, Bow top fencing, Driveway gates. Main hub: metal fencing and gates.

Nearby: Vertical bar fencing in Hackney, Vertical bar fencing in Islington, Vertical bar fencing in Waltham Forest.

Get In Touch